Top 9 Whirlpool Side Mounting Tall Tub Dishwasher Kit

Product Description

Allows mounting of dishwasher to side of cabinet.

From the Manufacturer

Allows mounting of dishwasher to side of cabinet.

Comparable to OEM Parts include WP8269145, 8269145, EA393134, AP3039168, PS393134, 830941, AH393134 and many more.

FIXES THE FOLLOWING SYMPTOMS:
Door latch failure.
Door won’t close.

INSTRUCTIONS:
1. Turn off the power and water supply to avoid shock.
2. Open the dishwasher door and use a phillips screw driver to remove the screws that hold the dishwasher to the cabinet.
3. Close the dishwasher door and use it to pull the dishwasher out from the counter top. You only need to pull out far enough to expose the brackets.
4. The undercounter brackets are held in by the bent tabs on the bracket that hold the bracket in place. Straighten out the tabs and slide the bracket out.
5. Slide the dishwasher brackets into the same area you removed the original brackets and bend the tabs to secure the brackets to the dishwasher.
6. Finish by carefully sliding your dishwasher back under the cabinet. Use your provided screws to screw the dishwasher bracket directly to the underside of your counter with a Phillips screwdriver.

WHAT YOU GET:
2 x Dishwasher Mounting Brackets
2 x Mounting Screws

100% CUSTOMER SATISFACTION :
Feel free to contact us if you have any questions or problems with the item

1) Turn off power to your dishwasher in breaker box (ABSOLUTELY CRITICAL TO AVOID SHOCK) 2) Rotate lower access panel fasteners and remove them 3) Remove access panel/sound dampening pad. Determine if the water supply/power lines have enough slack to move the dishwasher. If not, you will need to turn off water supply valve, disconnect water supply line from inlet valve & release power line from junction box 4) Open dishwasher door, remove the screws from the existing brackets (if present) 5) You will next be moving the dishwasher. To do so, you may need to lower the dishwasher by adjusting the leveling legs 6) Carefully pull dishwasher a few inches away from the front of the cabinet 7) Use pliers to pull up tabs in back of the bracket (if present). Pull out old brackets 8) Insert new brackets. Use pliers to adjust the back tab to lock the brackets in place 9) Slide the dishwasher back into the cabinet (readjusting the leveling legs, if necessary). Replace the screws in your new brackets 10) Reverse steps 3, 2 and 1. ALL SET! This is a generic product manufactured and distributed by Impresa Products (TM). This is not a Whirlpool (TM), Sears (TM), Kenmore (TM), Amana (TM), Jenn-Air (TM), Crosley (TM), Maytag (TM), Roper (TM), Magic Chef (TM), Estate (TM) or Inglis (TM) OEM product and Impresa Products has no affiliation with or endorsement from these brands. Our product is not covered under any other manufacturer’s warranty (except for Impresa Products). The Whirlpool (TM), Sears (TM), Kenmore (TM), Amana (TM), Jenn-Air (TM), Crosley (TM), Maytag (TM), Roper (TM), Magic Chef (TM), Estate (TM) and Inglis (TM) brand names and logos are the registered trademarks of their owners. Any use of the Whirlpool (TM), Sears (TM), Kenmore (TM), Amana (TM), Jenn-Air (TM), Crosley (TM), Maytag (TM), Roper (TM), Magic Chef (TM), Estate (TM) and Inglis (TM) brand names, model or any other related designations are made solely for purposes of describing and illustrating compatibility.

SPECIFICATIONS

1) Turn off power to dishwasher in breaker box (ABSOLUTELY CRITICAL TO AVOID SHOCK) and turn off water supply. 2) Pull dishwasher out from its place. 3) Remove upper screw from side of dishwasher. Align last hole of bracket on long flat part of bracket with screw hole. Reinsert & tighten removed screw or one of new provided screws. 4) Push dishwasher back into place. Open dishwasher door. Determine which bracket hole you will use. You want to use the farthest hole forward that still attaches to cabinet. If using holes on the smaller flat part of bracket, see 5A-6A. If you need to use back hole, see 5B-9B. 5A) If using front hole, leave bracket as is. If using 2nd hole, use 1 pair of pliers to hold bracket at the 2nd hole & 1 pair of pliers to break off front tab. Repeat. Push dishwasher back into place. 6A) Pre-drill screw holes to avoid splitting wood. Screw brackets into place using provided screws. DONE! 5B) If you cannot use either of front two holes on bracket, you will need to drill a hole in the tub. Use a sharpie to mark through back bracket hole on dishwasher. Repeat. Remove both brackets. 6B) Using 2 sets of pliers, break off both brackets before bend. 7B) Drill 3/8 inch hole through each side of plastic tub. Hold plastic tightly right below mark & use a drill slowly to ensure you have a nice clean hole without damaging the tub. Clean up both holes with razor blade until smooth. 8B) Put brackets back on, put dishwasher back into place. Pre-drill small holes into the cabinet wood, then screw in included screws on each side. 9B) Insert plastic plugs in each hole. Run dishwasher & check for leaks. If leaks are present, you may need to add rubber cement to plastic plugs to create a seal. This is a generic product manufactured & distributed by Impresa Products (TM). This is not a Frigidaire (TM) / Electrolux (TM) OEM product. Any use of Frigidaire (TM) or Electrolux (TM) brand names, models, etc. are made solely to describe & illustrate compatibility.

Replaces the following part numbers:
WP8269145, WP8269145VP.

Works for brands:
KitchenAid, Whirlpool, Kenmore, Maytag, Jenn-Air, Amana, Estate, Magic Chef, Inglis, Crosley, Roper.

Fixes problem with:
Door latch failure.
Door won’t close.

Contact Us
If you are not sure if part is correct, ask us in Customer questions & answers section or contact us by visiting the Discount Parts Direct storefront.

Business Wholesale
We are a small local company from Houston, Texas offer discount parts for retail and wholesale. If you need to purchase parts for business , please contact us for lower rates.

Part 8269145 comes in a pack of two. Mounting brackets secure the top of the dishwasher to the underside of a cabinet or countertop. If your dishwasher moves, shakes, or tilts forward, it may be time to replace one or both of the mounting brackets. The PartsBroz 8269145 bracket set fits and performs just like the original. Use it with a variety of top name brand dishwashers.

Installation Tips

Before beginning the repair, disconnect the dishwasher from its power source. Depending on the model, you may also need to disconnect the water supply. You’ll need a pair of needle nose pliers and a screwdriver to complete the repair. Make note that brackets typically wear down at the same rate, so be sure to check both brackets and replace both if needed.

Replacing your dishwasher’s mounting brackets is a simple way to get your dishwasher running like normal.

Have any of these problems? These brackets can help:

• Door won’t latch shut
• Door won’t close
• Noisy dishwasher

Part 8269145 is a functional equivalent for part numbers: 8269145, WP8269145, AP3039168, PS393134, 830941, AH393134, and EA393134.

Compatibility

It works with top dishwasher brands and many of their models. These include:

• Whirlpool
• KitchenAid
• Kenmore
• Maytag
• Jenn-Air
• Amana
• Estate
• Magic Chef
• Inglis
• Crosley
• Roper

Please reach out to us if you have a question about compatibility. Comment below in the customer questions and answer section, or send us a message on the PartsBroz storefront. We’re happy to help ensure you select the right part number for your dishwasher.